dumpvdl2-2.3.0-1.2 RPM for s390x

From OpenSuSE Ports Tumbleweed for s390x

A VDL Mode 2 message decoder and protocol analyzer.

Features:
 * Supports following SDR hardware:
   - RTLSDR (via rtl-sdr library)
   - Mirics SDR (via libmirisdr-4)
   - reads prerecorded IQ data from file
 * Decodes up to 8 VDL2 channels simultaneously
 * Outputs messages to standard output or to a file (with optional daily
   or hourly file rotation)
 * Outputs ACARS messages to PlanePlotter over UDP/IP socket
 * Supports message filtering by type or direction (uplink, downlink)
 * Outputs decoding statistics using Etsy StatsD protocol

Provides

• dumpvdl2
• dumpvdl2(s390-64)

Requires

• libSoapySDR.so.0.8()(64bit)
• libacars-2.so.2()(64bit)
• libacars-2.so.2(ACARS_2.0)(64bit)
• libacars-2.so.2(ACARS_2.1)(64bit)
• libc.so.6()(64bit)
• libc.so.6(GLIBC_2.2)(64bit)
• libc.so.6(GLIBC_2.3.4)(64bit)
• libc.so.6(GLIBC_2.34)(64bit)
• libc.so.6(GLIBC_2.4)(64bit)
• libc.so.6(GLIBC_2.7)(64bit)
• libglib-2.0.so.0()(64bit)
• libm.so.6()(64bit)
• libm.so.6(GLIBC_2.2)(64bit)
• libm.so.6(GLIBC_2.27)(64bit)
• libm.so.6(GLIBC_2.35)(64bit)
• libprotobuf-c.so.1()(64bit)
• libprotobuf-c.so.1(LIBPROTOBUF_C_1.0.0)(64bit)
• libprotobuf-c.so.1(LIBPROTOBUF_C_1.3.0)(64bit)
• librtlsdr.so.2()(64bit)
• libsqlite3.so.0()(64bit)
• libzmq.so.5()(64bit)
• rpmlib(CompressedFileNames) <= 3.0.4-1
• rpmlib(FileDigests) <= 4.6.0-1
• rpmlib(PayloadFilesHavePrefix) <= 4.0-1
• rpmlib(PayloadIsZstd) <= 5.4.18-1

License

GPL-3.0-only

Changelog

* Sun Aug 27 2023 Martin Hauke <mardnh@gmx.de>
  - Update to version 2.3.0
    * Allow reading raw frames or I/Q data from standard input. To
      enable this, specify "-" as the argument to --iq-file or
    - -raw-frames-file option, respectively.
    * Added --prettify-json command line option which enables
      prettification of JSON payloads in libacars >= 2.2.0.
      This currently applies to OHMA messages only.
    * Fixed incompatibility with libacars 2.2.0 which might cause a
      crash during reassembly of CLNP packets.
* Wed Jun 15 2022 Martin Hauke <mardnh@gmx.de>
  - Update to version 2.2.0
    * Added support for reassembly of multipart CLNP and COTP packets.
      This brings the ability to decode ADS-C v2 messages which are
      too large to fit in a single CLNP / COTP packet, even if
      fragmented in the X.25 layer.
    * Added proper formatting of Route Clearance CPDLC message
      elements.  Removed the obsolete 8-channel limit. The maximum
      number of VDL2 channels that can be decoded simultaneously is
      now limited only by the hardware.
    * Station ID (specified with --station-id option) is now
      appended to the StatsD namespace if StatsD metric collection
      is enabled. For example, if the station ID is set to KLAX, the
      new namespace would be "dumpvdl2.KLAX" instead of just
      "dumpvdl2". This allows simultaneous monitoring of several
      dumpvdl2 instances separately in Grafana.
    * Fixed a crash which occurred when the ground station list
      file could not be opened.
* Sun Jul 11 2021 Martin Hauke <mardnh@gmx.de>
  - Update to version 2.1.1
    * Fixed wrong ZeroMQ version check, which incorrectly declared
      ZMQ version 4.0.x as too old.
* Sat Nov 07 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 2.1.0
    * Added full JSON formatting for all protocols and message types.
      This is supported on all output types - file, udp and zmq.
      Together with multiple outputs feature that was introduced in
      version 2.0.0 this enables arbitrarily flexible arrangements,
      like logging to a file as text, logging to another file as JSON
      and sending JSON across the network using UDP and/or ZMQ. When
      collecting data from multiple receivers, --station-id option
      may be used to assign unique names to receivers in order to
      discriminate input from each one.
    * Removed a few duplicate routines that have their counterparts
      in libacars.
* Tue Aug 25 2020 Martin Hauke <mardnh@gmx.de>
  - Update to versino 2.0.1
    * Fixed build failure with gcc version 10.
* Mon Aug 24 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 2.0.0
    * Major overhaul of the output subsystem. The new architecture
      is modular, multithreaded and can easily be extended with new
      output drivers. It also allows using multiple outputs
      simultaneously.
    * New output configuration scheme. --output-file --daily,
    - -hourly and --output-acars-pp options have been removed.
      All outputs are now configured using --output option.
      Adjusting command line parameters is therefore required to run
      the program. Run dumpvdl2 --output help for instructions or
      see "Output configuration" section in README.md for details
      and examples.
    * Support for streaming messages over network using UDP/IP.
    * Support for streaming messages over network using ZeroMQ
      publisher sockets. Requires libzmq library.
    * Support for storing AVLC frames as raw data (without decoding)
      in binary files for archiving purposes. File contents can
      then be decoded anytime later, as if the frames were just
    * received from the air. Requires protobuf-c library.
    * Minor bugfixes.
* Sun Jul 05 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 1.10.1
    * Added support for SDRPlay API version 3 which is required for
      new devices (notably RSPdx). API version 2 is still supported,
      however it will probably be removed in a future release. It is
      possible to have both versions installed simultaneously and to
      choose which one to use at runtime. See README.md for details.
    * Added --milliseconds option which enables printing timestamps
      in message headers up to a millisecond precision. Note that the
      arrival timestamp is stored per VDL2 burst, not per VDL2
      message. Since a VDL2 burst may contains more than one VDL2
      message, all messages extracted from a single burst will still
      have exactly the same timestamp value, regardless of whether
      millisecond precision has been enabled or not.
* Fri Feb 14 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 1.9.0
    * Added decoder for ISO 8650 / X.227 Association Control Service
      (ACSE).
    * Improved decoder for ISO 8327 / X.225 Session Protocol.
    * Restructured code of ATN applications decoder. The previous
      implementation was a little messy and was unable to handle a
      few uncommon types of messages (like ACSE Abort PDU with no
      payload). This should bring the number of undecoded ATN
      messages down to zero.
    * Enable debugging output from SDRPlay driver only if
    - -debug sdr option is used.
    * Fix formatting of geo coordinates in ADS-C v2 messages.
* Mon Jan 27 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 1.8.2
    * Fix another crash opportunity due to missing sanity check on
      unparseable ACARS messages.
    * Fix ACARS output to Planeplotter. Only first three characters
      of Message Serial Number (MSN) field were sent instead of all
      four.
* Fri Jan 24 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 1.8.1
    * Fix a bug where an unparseable ACARS message could cause the
      program to crash.
* Sun Jan 19 2020 Martin Hauke <mardnh@gmx.de>
  - Update to version 1.8.0
    * Support for ATN-B2 Automatic Dependent Surveillance-Contract
      (ADS-C) version 2.
    * Support for automatic reassembly of multiblock ACARS messages,
      MIAM file transfers and fragmented X.25 packets. Contents of
      reassembled messages is now logged in one piece and passed
      upwards to decoders of higher layer protocols / applications.
      Thanks to this, many large messages which so far were decoded
      partially and logged with "Unparseable ... PDU" errors due to
      fragmentation, are now decoded correctly.
    * StatsD metrics for monitoring reassembly engine performance
      have been added.
    * Logged messages may be enriched with ground stations details
      read from a text file in MultiPSK GS format. Look up --gs-file
      and --addrinfo options in README.md and dumpvdl2 usage text for
      more details.
    * Logged messages may be enriched with aircraft details read from
      a Basestation SQLite database. SQLite3 library must be installed
      prior to compiling dumpvdl2 in order for this feature to be
      enabled. Look up --bs-db and --addrinfo options in README.md and
      dumpvdl2 usage text for more details. Database entries are
      cached in memory. There are new StatsD metrics for monitoring
      performance and utilization of the cache.
    * New --prettify-xml option enables pretty-printing of XML
      documents carried in ACARS and MIAM CORE messages. The purpose
      is to improve readability. If enabled, XML content will be
      printed as multiline text with proper indentation.  This
      requires libacars built with libxml2 support.
    * ACARS sublabel and MFI fields are now stripped from message text
      and logged as separate fields (if present).
    * When compiled with debugging support, dumpvdl2 now has a new
    - -debug command line option allowing configurable verbosity of
      debug messages. No debug output is produced by default.
    * Added extras subdirectory to the source tree. Additional content
      related to dumpvdl2 will be stored here. Currently bundled
      extras are: multitail color scheme for dumpvdl2 log files and
      vdl2grep script for grepping dumpvdl2 log files.
    * Bug fixes, code cleanups.

Files

/usr/bin/dumpvdl2
/usr/share/doc/packages/dumpvdl2
/usr/share/doc/packages/dumpvdl2/README.md
/usr/share/licenses/dumpvdl2
/usr/share/licenses/dumpvdl2/LICENSE

Generated by rpm2html 1.8.1

Fabrice Bellet, Sat Mar 9 12:50:11 2024